Writing

Well thank you to all of you. I am really enjoying this blog, learning how to watch it, and track it and such. I am sincerely flattered by the huge number of people who are out there looking for me specifically on Google or other search engines. And what is really cool as that when you find me, you read through my whole site, and then, even better, you keep on coming back. Thank you.

I will continue writing for you. I enjoy it. Sometimes I simply ramble on, like this morning, and of course other times I have something more specific to say. I have many ideas for articles that will be coming. I still intend to break the blog into three sections: a technical section, for the racers and fans who really want to get into the nuts and bolts of race cars. There will be what I like to call the personal growth section, in which I will discuss things mostly about my training and motivation. Things like meditation techniques I use, diet, exercise, and other things I use, or have tried or heard of, in that area. The third section will be about my own racing program. At this point I have two different cars lined up to drive next season, Dennis Hicks’ Mountain Brew dragster of course, and a jet funny car. I am also discussing options with two different top fuel teams, one running in IHRA out of Florida, and a local nostalgia top fuel car. So although the season is winding down for me, there will be plenty to watch out for.

This last week has been very busy on the phone and in meetings with team owners and sponsors, I apologize for not updating my blog as promptly as I would have liked.

By far the most popular articles I have written are the technical articles. I promise many more, starting with an in-depth how to on ladder bars and four links. The technical articles are much more involved to write. My objective is to make them as easy to read and understand as possible. I have yet to work out how to add decent drawings to my blog, so I may simply draw them then take a photo, probably much faster. It is also important to me that you are getting the correct information, in the correct order. So I will often do some research into specific details, which in turn leads me to a distraction, and hence it takes much longer to write a technical article. But they are coming, I promise. Of course if there are other technical subjects you would like to hear about, please, let me know. I will continue with the rear suspension theme for now. But there is very few aspects of the drag race car I cannot enlighten you on, from blown alcohol or nitro motor setup, clutch, carburetors too. Also things that one might consider simple, yet I often see them done incorrectly.

One thing in particular which was brought to my attention this weekend after a nasty incident, is the need for correct throttle linkage setups, with good strong toe hooks so the driver can pull the throttle back if he needs to. And in reality he should be pulling the throttle back whenever he closes it, not simply lifting his foot, but pulling back on it. As a driver, throttle control is very important to me. Having a correctly designed throttle linkage is mandatory if you want me to do a good job driving.

The unfortunate thing is that the small details do not get noticed until they are needed. And when they are needed is when it is a bad situation. When these cars are running right, when the tuneup is spot on, traction is ideal, they are almost easy to drive. It is when things are not right that you need all your ducks in a row, that toe hook on the throttle pedal only needs to work properly when the throttle is stuck open, until then you will never notice if it is strong enough or not. . . or will you. I hope you are off to the car right now to check on it.

Internet Explorer

Sorry all. I have just discovered that the slide-show on my homepage does not work with internet explorer. I would have thought that the people who made the website would have checked that, but obviously they missed that too. Anyway, I have someone working on it now, and it should be fixed soon. In the meantime, try using Mozilla Firefox as a browser, my website works great there, and far fewer security issues too.

Welcome!

I am very excited to welcome Boomers Hot Rod Shop as a sponsor. These guys build world class hot rods. Show winners. It is a pleasure to bring them on board because I can recommend their work without hesitation. Their standards are as high as mine, and that is rare. Jim Hilstad and the guys at Boomers can build a complete show winning hotrod from the ground up, from sourcing the original parts and pieces to the final polish. This is the important part, when I say world class, I mean “world” class. This is the shop to call if you want to win the biggest hot rod shows in the world, or if you just want to know that your car was built right the first time. They not only do hot rods, but rare and classic car restorations and repairs as well. Do you have a numbers matching car? As much an investment as a cool toy, these guys can repair it without risk to your investment. They understand the subtleties needed to maintain the status of your rare vehicle. Did your baby get damaged in an accident? They can do the repairs to the highest standard. Is it time to upgrade your hotrod, or classic car with some new suspension or fresh paint or interior? They can do that too. Want a rat rod? They will build you one. Don’t be intimidated by the high standards they keep though. These are down to earth hot rodders who understand exactly where you are coming from if you like your hotrod to be a daily driver too. These things are meant to be enjoyed, and driving them is a big part of that enjoyment.

Give Jim Hilstad a call at 1 604 886 4546 to discuss your hotrod needs. Tell him you got your number here.

I have a lot of fans over in the East of the continent too, if you want a world class hotrod, these guys will build it for you, it is worth calling them even if you are on the other side of the continent, they have many long distance clients and work with them very easily.

I just ran over to their shop and took a couple quick photos of the things they are working on today to give you an idea of their scope.

For fun, at the last race in Ashcroft on October 3, we are going to take their little International retro rod pickup up and I am going to give it a few laps down the quarter mile. I encourage all of you to come by and take a look. This is one cool little truck.

They are in the process of building a website, watch this space for the link as soon as they have it up and running.

Weekend update,

Sorry for the delay in getting this update posted.

The weekend was sweet and sour. The bad news is we only got two hits at the track and hurt our engine pretty bad on the second hit.

We are still searching for the correct combination of launch RPM, tire pressure, wheelie bar height, and torque converter to get a good launch with all the new horsepower we have with this new engine. The first run on Saturday morning was tough. With a low launch rpm we weren’t as close to the converter as we wanted to be, about three feet out from the line the engine and converter came on yanking the front wheels up hard, as a result hitting the wheelie bar hard. This sent the car into really good tire shake, eventually breaking the tires loose as the car skated over toward the wall. I pedalled it a little, settled the car, and drove it out the back door. Hit the chute lever, and it wasn’t there. Thought I might have missed it so tried again, no, it definitely isn’t there. Hard on the brakes, the car went into some serious bouncing. Neil, who was in the other lane tells me it was a good 18 inches, two feet in the air at times, bouncing from tire to tire. Have I told you how much fun these cars are to drive? I kept it off the walls, had one moment where I thought I might crash, but in the end I got it stopped. Neil said he could smell the brakes while he was still doing a hundred miles an hour behind me. Tire shake is a pretty violent thing, I guess when it shook early in the run it knocked the bolt out of the parachute lever. Back to the pits.

Rain interrupted the rest of the day, but we got another hit in the evening. We stepped up the launch RPM and added some more tire pressure. The car yarded the front tires right off the start line, shook into spin again and slid toward the centrline, same again, pedaled settled the car and hit it again. Had a parachute this time, but the car vibrated really bad in the shutdown and I knew something was seriously wrong.

We broke a tie bar between the roller lifters, the lifter turned in the bore so when the cam came around it broke the wheel off the bottom of the lifter, the wheel went down between the connecting rods and did some serious damage, not sure just how bad yet but there is a hole in the side of the block. When we get it further apart we will see just how bad it is. Nice thing with an aluminum block is that it can be welded up. We will be back.

Ok, that’s enough of the doom and gloom.

Uniforms! Tom and Debbie from CV Transport supplied us with some fantastic new crew shirts. The artwork is incredibly clear, and they look great next to the car. We were all strutting about very proud this weekend. Thank you Tom and Debbie.

Rear Suspension

This whole website is pretty cool. By watching the stats I can see that the most popular tags for searches which end up on my site is rear suspension setup, in particular four link setups.

I will, in the next couple weeks, publish a very in depth post on adjusting your four link correctly. It will be a long post to be sure I cover it properly. But to begin with, let’s cover some basics.

As I am sure you have deduced, I am a drag racer, so this discussion refers to drag racing setups. If you want info for a street setup, or something to go around corners, send me an email and I can help you individually.

Let’s start with some basic high school physics. Newton’s law of motion states that for every action there is an equal and opposite reaction. This applies to almost everything we are doing while trying to accelerate a car down the quarter mile, and is very handy to remember when designing or modifying anything on the car.

Pistons are pushing down on the connecting rods, and the crankshaft, most of us understand that, but what are they pushing against? They push up against the cylinder heads, and, here it comes, they push up the same amount that they are pushing down, Newton got it right. That is an example for you, back to the rear suspension.

Your driveshaft is rotating, clockwise when viewed from the front. This turns the pinion gear in the front of your rear axle, the pinion gear is meshed with the ring gear, turning the rotation ninety degrees to drive the rear wheels. Try to picture the following, it can be tricky, but once you get it you will have a better understanding of what is happening in the rear suspension. As the pinion gear is rotating, meshed with the ring gear, if the slicks are stuck hard to the track, in effect preventing the ring gear from turning, or at least impeding the ring gear from turning, the pinion gear is literally trying to “climb up” the ring gear. Picture the ring gear as stationary, the pinion then climbs up the ring. Back to Newton, even when the tires start to rotate as the car accelerates forward, the pinion gear is still trying to climb up the ring gear, by an equal amount of force. Equal to, and opposite the amount of force trying to drive the car forward, (ok, there are some minute losses, friction and such, but for this discussion we can forget about them). And it is a huge amount of force, (torque). Think about that 750 ft lbs of torque your engine makes, multiplied through the torque converter, before hitting your first gearset which multiplies it even more, it is a huge amount of torque, (I am saving the calculations for another post). Now if the pinion is trying to climb up the ring gear, what is stopping it? The axle housing stops it, and in turn, whatever is holding the axle housing in the car. . . four links, ladder bar, leaf spring, etc.

Now, rather than visualizing the pinion climbing the ring gear, picture the whole axle housing trying to rotate up and around the rear axle, in the opposite direction to tire rotation, (and with an equal amount of force, Newton again). The housing is being driven around the rear axle by the pinion gear. It is this rotational force that we are harnessing with a four link or ladder bar or any other rear suspension setup.

A four link has two bars per side, a top bar and bottom bar. Pictured from the side, and under acceleration, (people often forget that under braking, or deceleration, everything happens the other way, ever see a car try to turn when backing off at the top end?), the bottom bar is being pushed forward, and being compressed by the rotational force of the axle housing, while the top bar is being pulled backwards and upwards in tension, trying to lift the chassis of the car. Adjusting the angle of the bars, controls the direction of the push and the pull, pushing the car forward, pulling up on the chassis, lifting the chassis, in turn transferring weight to the rear tires.

This all refers to the basic load directions in a four link rear suspension, so that you can picture what is happening back there when you release the trans brake, or mash the throttle. I have tried to make it basic enough to follow, yet assume the reader has a bit of an understanding of the terms I am using. These loads are all similar in a ladder bar setup, or leaf springs. Stock coil spring rear end setups, like some Mustangs and Camaros are in one form or another a four link, but with different geometry for anti-squat and anti-dive, as well as general passenger comfort. This is the first time I have ever really written a technical article, and hope I am making the concepts clear and understandable. I will work out how to add drawings in future articles to help clarify some of the concepts. If you have any questions, don’t quite understand what it is I am trying to get across, or want some clarification, please send me an email, I would love to hear. If you have any ideas for future posts, I would love to hear them too.

I will continue this discussion on rear suspensions soon, so check back often.

Twitter

I have been asked many times if I am on Twitter, when I have answered “no”, I am told I have to be on Twitter. So now I am on Twitter.

It could be quite interesting while I am at the track, I will have to work out how to add photos to the tweets from my phone. (see that, I am even using the right jargon, I called it a tweet). I would even use it through the week while I am in the shop if people are interested, (Although I think it might get a little boring. . . now I am welding, now I am grinding, now I am filing, now I am welding, building cars is not as glamorous as it might seem. No, it’s not all like that, today I am going to help a fellow who has a one owner 67 Chevelle, he has just spent the last couple years doing a complete restoration on it, should be a pretty nice car).

Back to Twitter. Where is everyone that wanted me to be on Twitter? I am flattered that three of you jumped on board right away, but I feel kinda funny tweeting to just three people.

I am racing in Ashcroft next weekend, (September 19 & 20), and you are all invited. Those of you who can’t make it, get on Twitter, and I will keep you up to date that way. Those who do come, make sure you come over and say hi. Make my pit your home base, unless you are sitting in the car you won’t really be in the way. Hang out all you want. I can see many people when I am at the track, really want to stay and watch, or just hang out, but start to feel uncomfortable, feel like they are being a bother, well your not. Now if I have to keep asking you to move so I can get to what I am doing, that might be different, but there is plenty of room. Everyone on the team is very friendly, Dennis, the car Owner is very proud of his car, ask him all about it and he will enjoy telling you everything you want to hear. Casey, my daughter, will be there, she can tell you all the stories about how many times I have scared her while I am driving these cars, and she can tell you about her driving experiences as well. So come on out and have a visit. $10 for a day of entertainment is great value.

If you can’t make it, find me on Twitter

Ladder bars.

Why not a four link?

I am a big fan of ladder bars. For the majority of racers out there a ladder bar will do everything they require. But a four link is better, I hear this all the time, and yes in some perspectives a four link is a much better drag racing rear suspension setup. The biggest advantage to a four link is it’s adjust-ability.  This can be a great advantage. . .  if you know how to adjust it. When I look around the track, I see very few people adjusting their four links. Generally what I see are four links that have been setup, either by someone who knows how to tune them, or after a certain amount of aggravation, or “that’s how I bought the car, and I am not going to touch it ’cause it is working just fine the way it is”., and because the car is going straight, and running consistent, the owner leaves it alone.

The problem with a four link is that very few people have spent the time to work out how to make adjustments. I am not going to get into how to adjust a four link here, but I will tell you that the procedure starts when the car is being built. The chassis builder should have given you a chart of instant centres. If you don’t have one, you need to get one. You can generate one yourself. There are computer programs you can buy that make it easier, or you can do it the old fashioned way on the floor. I have done both. I now have a computer program I find reasonably easy to use although it does not allow for as many holes as we are using in newer four link setups, so I have to run the program twice. Once you have your instant centre chart, you then need some sort of preload reference. How much weight, does a quarter turn on the bar add, or subtract, form each corner. Of course this will change with a change in instant centre, so if you change bar locations, you then need to know the preload adjustments for that location. The point I am trying to make here is that although a four link is a great rear suspension setup, the adjustment procedure is too involved many drag racers. They generally get it working, then never adjust it.

If that is going to be the case, why not use a ladder bar then? A ladder bar generally has three choices for instant centre, and you can see them all on the car, you don’t need a chart. Preload can be set with a ruler if you want, although I do prefer to weigh the car so I have a reference point for preload adjustments. Often, unless it is a very high horsepower car, little or no preload is required with a ladder bar.

Ladder bars do take up a little more space forward in the chassis, if you are building a car with a lot of rearward driver position it can be a challenge to get a long enough bar in the car.

One of the cars I am currently building is a ladder bar setup. It is a very short wheelbase at 100.5 inches, so getting bars in there can be done. This one is interesting in that the owner wanted to use his rear axle housing which was already setup for a four link. It has a range of holes on the axle housing that could be used, and they are not in the usual location for a ladder bar. I had to get creative. One problem the typical ladder bar has is because of the angle of the two bars, as soon as you adjust the rear of the bar for pinion angle, the hole spacing changes, causing a side load on the rod ends, this is not good at all. It can also cause a certain amount of stress and cursing when trying to install the bars after making an adjustment.

For this car, I wanted to take advantage of the range of holes in the housing. I accomplished this by putting a pivot in the top tube, allowing the hole spacing at the rear to be adjustable. This solves two problems, first there is now no side loading on the rear rod ends after adjustment, and second, because I made the top bar adjustable, pinion angle can be changed very easily. Now that I have built these bars, I wouldn’t build them any other way. They are a little more expensive, but worth it. They offer a large range of adjust-ability, without the confusion of a four link. They are very strong, with large diameter thick wall 4130 tubing. And they can be built to suit any set of brackets you may already have.

Questions? Ask away, at the contacts page

Since I published this post a few days ago, it is interesting to note that people are finding it when searching “how to adjust four links”. I will compose an in depth look at how to adjust a four link suspension for future post. It may take a while so check back often. If you have any specific questions concerning your setup, my email is on my contacts page.

Race cars

As some of you may know already, and for those of you who do not know yet, when I am not at the track driving race cars, I am in the shop building them. I have a small fabrication shop where i build very high quality, one-off race cars. I do not have an “off the shelf” model, or models, although it is something I may consider in the future, maybe with a basic nostalgia dragster chassis, or maybe a junior dragster chassis. It has been my experience though that every client wants something slightly different.

I am currently building a very cool street legal car, very loosely based on a fox bodied McClaren. the body has been developed overr the last ten years by the owner. The body is all carbon fibre kevlar, and only weighs 85 pounds, doors, hood,  and all. It is powered by an 650hp aluminum Fontana motor. Add the 150 shot of nitrous and it has 800hp, on pump gas. The plan is that this car will run 8.90’s in street trim. I will keep you updated on this one.

If any of you are looking for advice or help with your drag race setup, from choosing a chassis design, setting up your suspension, choosing a whole combination, or help with tuning your combination, feel free to drop me a note any time, through the contacts page, or start a forum discussion, I am sure there are plenty of people out there reading this site who can also offer up some opinions.

Advertising

Ah yes, more advertising, just what you wanted to see. I am experimenting with some advertising on my site. The truth is that maintaining this site and writing the blog takes up a huge amount of time, time that I feel I would like a return on. If you, the people who are reading this feel like you are getting a benefit from my site then I encourage you to take advantage of my donate button. To those of you who already have, I thank you sincerely. I believe that as the blog articles become even more interesting you will truly begin to see the value in using the donate button to keep this product happening. I am working toward making this site something worth checking in to often, and recommending to your friends. With all that in mind, I encourage you to click on the ads on my site. A mere click is all it takes to generate income for me to help me get a return on the time I am investing in this. You don’t even have to buy anything, or spend your money, simply click on the add. Every click, and every donation helps get me closer to the world championship I am working toward.  Thank you all.

Also, the links I have. I choose my links carefully, and soon will have a little section explaining why the link is on my site, but all the sites I have listed are worth clicking on and looking at. If you have a site you would like me to link to, send me a note I am interested. I am also interested in having my site linked to yours.

Thank you all for your support, let’s get clicking.

Fans

One thing that was very cool this past weekend was the many of my fans, you, who came by to say hello, and have a visit. It is always a pleasure when that happens even though I wasn’t driving. Thank you.